Insulated liners
Liners can be insulated with a blanket or a poured mix which improves draft and limits creosote.
A sweep in Greencastle can reline an unlined or damaged flue so smoke and gases vent safely from a fireplace, stove, insert, furnace or water heater. Call (223) 465-1032 to reach a local chimney sweep.
A chimney liner is the channel inside the chimney that carries smoke and combustion gases up and out. It keeps heat from reaching wood framing next to the chimney, protects the brick and mortar from corrosive gases and gives the appliance a flue of the right size to draft well. Many older homes, especially those built before the middle of the last century, have no liner at all.
There are a few reasons a chimney gets a new liner. The original clay tiles may be cracked from age, settling or a chimney fire, or the chimney may never have been lined. Changing appliances is another big one, because a flue sized for an old fireplace is usually too large for a modern insert or furnace.
A camera scan of the flue shows the sweep the condition of the old liner and any offsets or obstructions. The inspection tells you whether relining is truly needed and what kind of liner suits the chimney. Ask to see the camera video so you understand what was found.
Chimney Liner Installation is often paired with chimney liner repair and chimney inspection, depending on the cause.
Need chimney liner installation in Greencastle? Call (223) 465-1032 to reach a nearby chimney sweep.
Call nowA liner has to fit the flue, the appliance and the chimney route.
The inside of the chimney is checked so the route and condition are known. This confirms what kind of liner the chimney needs.
The liner diameter is matched to the appliance outlet or the fireplace opening, following the manufacturer guidance. The route and any offsets are noted.
Before the liner goes in, the chimney is swept and cleared. Some chimneys need old tiles broken out to fit an insulated liner.
The stainless liner is lowered from the roof down to the appliance, often wrapped in an insulation blanket. Many liner systems are tested with insulation for clearance to combustibles.
The bottom connects to the stove, insert or appliance, and the top is sealed with a top plate and cap. Every joint is secured so gases stay inside the liner.
A draft test confirms the new liner is working. Keep carbon monoxide alarms on every level of the home.
Liners can be insulated with a blanket or a poured mix which improves draft and limits creosote.
Straight flues can take rigid stainless pipe for a strong, smooth flue.
A cement based mix is poured around a form inside the chimney to create a smooth new flue in a single solid lining.
A flexible liner works in chimneys that are not perfectly straight and come in grades matched to the fuel.
Smaller liners for gas or oil furnaces and water heaters stop condensation from damaging the chimney.
Stainless steel is the most common material for relining today, because it is strong, resists corrosion and works with wood, gas and oil. Flexible stainless goes around offsets in a chimney, and rigid stainless suits straight runs. Liners are sold as tested systems, with grades suited to wood, gas or oil.
Insulating a stainless liner improves draft, cuts creosote buildup in wood flues and is part of many systems. A cap and top plate finish the job at the top of the chimney. Many Greencastle chimneys get a stainless liner when an old fireplace is converted to an insert.
Relining means putting a new liner into a chimney that has an old, damaged or missing one. Changing to an insert or stove, finding cracked tiles or recovering from a chimney fire usually leads to relining. Relining is usually far less disruptive than rebuilding the chimney.
Before relining, it helps to know which appliances share the chimney. If the furnace was upgraded recently, the water heater may now be venting into a flue that is too large. A smaller liner brings the draft back where it should be.
Around Greencastle, relining usually comes up when a home changes heating appliances or an inspection turns up cracked tiles. Across Greencastle and nearby towns such as State Line, Waynesboro, Wayne Heights and Chambersburg, long heating seasons and repeated freeze and thaw cycles are hard on clay tile and mortar, and a new liner is often the safest long term fix.
Searching for chimney liner installation near me from Greencastle or State Line, Waynesboro, Wayne Heights and Chambersburg? Call (223) 465-1032 to talk to a chimney sweep who works in your part of town.
Winters here are long and cold, and the heating season usually runs from October well into April. Masonry takes the worst of it from the freeze and thaw cycle: water soaks into brick, mortar joints and the crown on a mild day, freezes overnight and expands, and each winter widens the cracks a little more. Wind driven rain from coastal storms finds any gap in flashing, too. That is why chimney cleaning in Greencastle is usually booked in the fall, before the first cold night.
A chimney problem fixed early rarely spreads to the masonry, the liner or the house.
Local sweeps see the same chimney types and weather wear across Greencastle and nearby towns.
Ask the sweep about the cause, the options and the estimate before work starts.
More questions? Call (223) 465-1032
Fixing gaps, cracks and missing mortar inside the flue liner after a camera scan shows where the damage is.
Learn moreA level 1, 2 or 3 review of the full chimney system to catch cracks, blockages and leaks before they turn into hazards.
Learn moreInstalling wood, gas and pellet inserts in existing fireplaces, with the chimney inspected before anything goes in.
Learn moreInstalling freestanding wood stoves with the right clearances, hearth and venting, following the stove manual and local code.
Learn moreLooking for something else?
See all chimney servicesCall now for Greencastle chimney liner installation and help in the towns around it.
Free to call. No forms to fill out.